Launch offer — valid today only

📄 Digital book in PDF · read it on your phone or print it

Your Compact Tractor in Drawings: Hitch, PTO, Loader and Slopes in the Right Order One Job on Every Page

Made for Australian blocks, all in metric (kPa, centimetres, metres), with dams and fire danger days covered. Controls, start-up and shut-down, the three-point hitch, the PTO, the loader and ballast, slopes and dam walls, the slasher and owner maintenance. One topic per page: the drawing first, then what to remember. 70 illustrated pages.

SHOW ME THE 70 PAGES

🔒 Secure checkout · PDF by email · 30-day guarantee

Every topic, its own pageEach routine drawn, with the explanation beside it
70 illustrated pages9 parts, from the controls to the quick checks
Up-to-date sourcesSafe Work Australia, state WHS regulators and AS 1636
PDF by emailFormat

Look Inside the Book

Every page has a big drawing and a box with the steps and numbers you need to know:

PTO off, implements down, neutral, park brake, engine off and key out, check it's stopped.
PTO off, implements down, neutral, park brake, engine off and key out, check it's stopped.
Cat 1 pins: about 22 mm lower, 19 mm top. Check your manual.
Cat 1 pins: about 22 mm lower, 19 mm top. Check your manual.
PTO off, engine off, shaft stopped before you go near it.
PTO off, engine off, shaft stopped before you go near it.
Mulch to wet soil: same bucket, several times the weight. Check your rated lift.
Mulch to wet soil: same bucket, several times the weight. Check your rated lift.
Full bucket at the front, ballast at the back: the manual gives your minimum.
Full bucket at the front, ballast at the back: the manual gives your minimum.
Before mowing: walk, flag stumps, holes, pickets and wire, check power lines
Before mowing: walk, flag stumps, holes, pickets and wire, check power lines
Walk-around, fluids, tyres in kPa, fire check and controls as tick boxes to print.
Walk-around, fluids, tyres in kPa, fire check and controls as tick boxes to print.
A decision chart for slopes and loaders that ends in go, change the plan, or don't.
A decision chart for slopes and loaders that ends in go, change the plan, or don't.

Swipe to see more →

These are real pages from the book. The table of contents is the full one: 9 parts and 66 topics.

The Problem Isn't You. It's How It Was Explained.

You're behind the tractor, the slasher's just gone quiet, and a clump of grass is wrapped around the PTO shaft. Your hand is already halfway there.

The manual covers it in three paragraphs of warnings, somewhere between the warranty and the grease chart. Nothing tells you what to do, in what order, right now.

PTO off, engine off, shaft stopped before you go near it.

In the book, that same shaft is one page: PTO off, engine off, shaft stopped, drawn in that order. Beside it, the wrong move is drawn too: the loose sleeve, the spinning yoke, the one second it takes.

The three-point hitch, rear ballast behind a loader, slopes and dam walls, the shut-down routine and the daily checks each get their own page as well.

You see it, it makes sense, and you do it right on the block without hunting for the manual in the shed.

COMPARE FOR YOURSELF

Same Topic, Two Ways to Learn It

THIS
  • The manual: line after line
  • Hitch adjustments explained only in words
  • You head out to the shed still unsure
The three-point linkage comprises two lower links and one upper (top) link, which together locate the implement relative to the tractor. The lower links, raised and lowered by the hydraulic lift arms via adjustable lift rods, support the mass of the implement, while the top link, adjustable in length, determines its pitch. Lateral movement is restricted by stabilisers or check chains, which must be adjusted in accordance with the operator's manual and the implement category to prevent excessive sway during operation and transport.
FOR THIS
  • The three-point hitch in one drawing
  • The steps in a numbered box
  • You see it and it makes sense
Cat 1 pins: about 22 mm lower, 19 mm top. Check your manual.
CONTENTS

Take a Look at the 9 Parts and 66 Topics

Nine parts: Know Your Machine · Before You Turn the Key · Start, Drive and Stop · Three-Point Hitch and PTO · Front Loader and Ballast · Slopes and Dams · Implements on Your Block · Owner Maintenance · Quick Checks. 70 pages, all illustrated.

IKnow Your Machine · pp. 5-11
  1. Your compact tractor at a glance
  2. The ROPS and the seatbelt work as a pair
  3. The controls, colour by colour
  4. Gear or hydrostatic: how your tractor moves
  5. Reading the dash and warning lights
  6. The decals are the short version of the manual
  7. Which manual pages to read first
IIBefore You Turn the Key · pp. 12-18
  1. The walk-around in 8 steps
  2. Fluid checks: engine oil, coolant, hydraulic oil
  3. Fuel: diesel, clean and topped up
  4. Tyre pressures in kPa
  5. Air filter and radiator screen
  6. Fire risk check before you work
  7. Dress for the tractor
IIIStart, Drive, Stop · pp. 19-26
  1. Getting on and off: three points of contact
  2. The start-up routine in 7 steps
  3. Moving off and stopping smoothly
  4. Brake pedals: locked together or split
  5. Diff lock: when to use it and when to let go
  6. The shut-down routine in 6 steps
  7. Children, visitors and riders
  8. Driving on a public road
IVThree-Point Hitch and PTO · pp. 27-35
  1. The three-point hitch explained
  2. Hitch categories: will this implement fit?
  3. Hitching an implement in 8 steps
  4. The top link sets the angle
  5. Stabilisers and sway: centred and tight enough
  6. Position control vs draft control
  7. The PTO: 540 rpm and what it means
  8. PTO shaft length, guards and shear bolts
  9. PTO entanglement: the one second rule
VFront Loader and Ballast · pp. 36-43
  1. Loader controls on one joystick
  2. Carry low, always
  3. Loader capacity and what dirt weighs
  4. Why you need rear ballast with a loader
  5. Ballast options: box, wheel weights, liquid tyres
  6. Never lift round bales or people with a bucket
  7. Fitting and removing the loader
  8. Hydraulic leaks: never use your hand
VISlopes, Dams and Rough Ground · pp. 44-50
  1. Why tractors roll over
  2. Up and down, not across
  3. Loader on a slope: bucket uphill
  4. Dam walls and banks
  5. Gullies, wet ground and soft soil
  6. Rearward flip when towing or stuck
  7. Spotting hazards before you mow
VIIImplements on Your Block · pp. 51-58
  1. The slasher: set-up in 5 steps
  2. Slashing safely: thrown objects and blade stops
  3. The rotary tiller (rotary hoe)
  4. The box blade: cut, carry, spread
  5. Rear blade: angle, tilt and offset
  6. The post hole digger
  7. Pallet forks and the bale spear
  8. Towing a trailer
VIIIOwner-Level Maintenance · pp. 59-65
  1. Hours, not kilometres
  2. Greasing: find every nipple
  3. Changing engine oil and filter
  4. Fuel filters and the water separator
  5. Battery and electrics
  6. Storing the tractor in the shed
  7. Where owner jobs end
IXReview and Quick Checks · pp. 66-70
  1. The 10 most common owner mistakes
  2. Pre-start checklist on one page
  3. Hitch and PTO checklist
  4. Slope and loader decisions at a glance
  5. Your tractor's numbers

One Page, One Topic, All Clear

Think of it this way:

It's Saturday morning, the grass in the back paddock is knee-high and the slasher is sitting on the shed floor. You need it on the hitch, level and safe, before the day warms up.

You open the book to the slasher set-up page and it's all there: lower arms on first, the top link setting the angle, the stabilisers pulled in, the PTO shaft guarded. Five numbered steps, drawn in order.

Full bucket at the front, ballast at the back: the manual gives your minimum.

Same with carrying a full bucket, adding rear ballast, crossing a dam wall, greasing every nipple or shutting down: each one on its own page.

Compact Tractor Illustrated is 9 parts and 66 topics, all drawn, with a one-page pre-start checklist, the most common owner mistakes and quick checks at the end.

What you see drawn, you don't have to memorize.

What's Inside Compact Tractor Illustrated:

Ipp. 5-11

Know Your Machine

Your tractor at a glance, the ROPS and seatbelt as a pair, the controls colour by colour, gear or hydrostatic, the dash lights, the decals and which manual pages to read first.

IIpp. 12-18

Before You Turn the Key

The walk-around in 8 steps, oil, coolant and hydraulic checks, clean diesel, tyre pressures in kPa, the air filter and radiator screen, the fire risk check and what to wear.

IIIpp. 19-26

Start, Drive, Stop

Three points of contact, the start-up routine in 7 steps, moving off and stopping, brake pedals, the diff lock, the shut-down in 6 steps, riders and public roads.

IVpp. 27-35

Three-Point Hitch and PTO

How the three-point hitch works, hitch categories, hitching in 8 steps, the top link, stabilisers, position and draft control, the PTO at 540 rpm, guards and shear bolts, and the one second rule.

Vpp. 36-43

Front Loader and Ballast

The loader joystick, carrying low, what dirt weighs, why you need rear ballast and which kind, what never goes in a bucket, fitting the loader and hydraulic leaks.

VIpp. 44-50

Slopes, Dams and Rough Ground

Why tractors roll over, up and down not across, bucket uphill, dam walls and banks, gullies and soft soil, rearward flips and spotting hazards before you mow.

VIIpp. 51-58

Implements on Your Block

The slasher set-up in 5 steps and slashing safely, the rotary hoe, box blade, rear blade, post hole digger, pallet forks and bale spear, and towing a trailer.

VIIIpp. 59-65

Owner-Level Maintenance

Hours not kilometres, finding every grease nipple, oil and filter, fuel filters and the water separator, the battery, storing it in the shed and where owner jobs end.

IXpp. 66-70

Review and Quick Checks

The 10 most common owner mistakes, the pre-start checklist, the hitch and PTO checklist, slope and loader decisions at a glance, and a page for your tractor's numbers.

At the end of the book: The 10 most common owner mistakes, one-page checklists and a page for your tractor's numbers.

SHOW ME WHAT'S INSIDE

Plus: 2 Free Books

What Would You Do? 30 Paddock Scenarios

BONUS 1: «What Would You Do? 30 Paddock Scenarios»

Value on its own: US$ 17.90

Real situations on your block (a wet gully, a full bucket on a slope, a stubborn top link) to work through before you face them on the tractor.

Tractor Mistakes & Pre-Start Cards

BONUS 2: «Tractor Mistakes & Pre-Start Cards»

Value on its own: US$ 14.90

The most common owner mistakes drawn before and after, plus printable pre-start cards to keep in the cab or on the shed wall.

Compact Tractor Illustrated with 2 Free Books

  • Compact Tractor Illustrated: 70 illustrated pagesUS$ 63
  • BONUS 1: What Would You Do? 30 Paddock ScenariosUS$ 17.90
  • BONUS 2: Tractor Mistakes & Pre-Start CardsUS$ 14.90
  • High-resolution PDF to printIncluded
Total value US$ 95.80
YOUR PRICE:
US$ 27
You save US$ 68.80
YES, I WANT COMPACT TRACTOR ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

Secure purchaseEncrypted payment30-day guarantee

PDF by email: We email you Compact Tractor Illustrated as a PDF, together with the two free books. It's a single payment: no installments, no extra charges.

Who This Book Is For

You've just bought your first tractor

You've just bought your first tractor

You start with the parts and controls, then the start-up and shut-down routines, so the first hours on the seat aren't guesswork.

You've got a paddock to slash this weekend

You've got a paddock to slash this weekend

Open the hitch, PTO and slasher pages in the shed and follow the numbered steps with the book beside you.

You've run it for a few years

You've run it for a few years

The slope, loader and ballast pages show what you may never have been told, and the maintenance part keeps your owner jobs in order.

Everything You Get Today

US$ 95.80US$ 27
YES, I WANT COMPACT TRACTOR ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

30DAYS
GUARANTEE

30-Day Guarantee

Try Compact Tractor Illustrated for 30 days, bonus books included.

We refund everything if the file won't open, if the book isn't what you see here, if you were charged twice or if the email doesn't arrive. Just email us.

You pay once. No subscriptions.

Frequently Asked Questions

Is it for me if I've only just bought my first tractor?

Yes. It starts with the parts and controls and builds up to ballast, implements and owner maintenance. If you've had your tractor for years, the slope, loader and PTO pages are still worth a look.

Where does the content come from?

From Safe Work Australia guidance on tractor safety, the farm tractor guides of the state WHS regulators and AS 1636 for roll-over protection. Every spec is marked to check against your own operator's manual, because each tractor is different.

Is it official material?

No. It's an independent illustrated book. It isn't affiliated with or endorsed by any regulator, standards body or tractor brand, and it names no brand or model.

Does it replace hands-on training?

No. It doesn't replace operator training, a dealer induction or your operator's manual. It helps you understand what you're doing and follow the routines in the right order.

Will it suit my tractor, and is it made for Australia?

It explains how any compact tractor works, gear or hydrostatic, whatever the brand, and every spec is marked to check against your own operator's manual. It's all metric (kPa, centimetres, metres, kilograms) and written for Australian blocks: paddocks, dams, gullies and fire danger days.

When and how does it arrive?

As a PDF by email, to the address you enter at checkout. The 2 bonus books come with it.

Do I have to pay every month?

No. It's a one-off payment, with no subscription.

Can I have it on paper?

Yes. Print it at home or at a print shop and keep it in the shed or on the workbench. The pre-start cards are made to print.

How does the refund work?

You have 30 days. We refund everything if the file won't open, if the book isn't what you see on this page, if you were charged twice or if the email doesn't arrive: just email us.

Before You Close This Page

No more rereading the manual and still guessing.

The hitch, the PTO and the loader: drawn, and done.

You get on the tractor knowing where everything is.

Drawings make studying faster.

The book is right below.

One-time payment: US$ 27 · Guarantee: 30 days · PDF by email

YES, I WANT COMPACT TRACTOR ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.